PHOENIX – 1525610 – PROFIBUS, Electrical Connectors-Contactors – ICDC-040119 – New
Main Category: Electrical | Sub-Category: Connectors-Contactors | Status: New Original Components
PHOENIX Part Number: 1525610 | ICDC Internal Part Number: ICDC-040119
1525610 Description:
Flush-mounting female connector for bus system – SACCEC-M12FSB-2CON-M16 / 5,0-910
1525610
Bus system flush socket, PROFIBUS, 2-pin, M12, shielded, B-coded, front / screw mounting, with M16 thread, can be positioned, with 5 m bus cable, 2 x 0.25 mm 2
Note for operation The electrical and mechanical data indicated require a pair of connectors correctly locked and mounted. If the connector is in the unlocked state and there is a danger of pollution, the connector must be closed with a protective cap> IP54. Also take into account the influences via wires, lines or mounting on the PCB
Safety warning
Safety information WARNING: The connectors must not be connected or disconnected under load. Non-compliance and non-compliant use may result in damage to people and / or property.
• WARNING: Only use products that are in perfect condition. Check the products regularly for damage. Take defective products out of service immediately. Replace the damaged products. The item cannot be repaired.
• WARNING: Only have this product installed and operated by qualified electrical engineers in accordance with the safety instructions below. Specialized personnel must be familiar with the basic notions of electrical engineering and must be able to recognize and avoid dangers. The corresponding symbol on the packaging indicates that the intervention of qualified personnel in the electrotechnical field is required.
• The products are suitable for the areas of plant assembly, control and assembly of electrical devices.
• When operating the connector outdoors, these rooms must be protected from environmental influences.
• Packaged products must not be handled or opened incorrectly.
• Use only male connectors specified in the standards indicated in the technical data, (eg those listed in the product accessories at the website phoenixcontact.com/products).
• In case of direct use of the product in conjunction with third party products, the responsibility lies entirely with the user.
• For operating voltages> 50 VAC the conductive connector housings must be grounded
• Make sure that, when laying the cable, the tensile load does not exceed the limits established by the regulations.
• Observe the respective technical data. The indications are given in the following points:
o On the product
o On the packaging label
o In the documentation provided
o Im Web phoenixcontact.com/products under the product heading
• Use only the tool recommended by Phoenix Contact
• Do not close unconnected connectors with a safety cap. Suitable accessories for the product are listed in the accessories area of the network item under phoenixcontact.com/products
• Make sure that the protective or functional earth is inserted correctly.
• VDE 0100 / 1.97 § 411.1.3.2 and DIN EN 60 204 / 11.98 § 14.1.3 apply to group several electrical circuits in a cable and / or connector.
• The connector heats up during normal operation. Depending on the environmental conditions, the surface of the connector can experience continuous heating. In this case, the user is responsible for applying the safety information (eg DIN EN ISO 13732-1: 2008-12).
Product type Circular connectors (device side)
No. poles 2
Number of cable outlets 1
Shielded Yes
Coding B – reverse
Features of insulation
Overvoltage category II
Degree of pollution 3
Degree of protection IP67
Degree of protection IP65 / IP67
Ambient temperature (operation) -25 ° C … 85 ° C (female connector / connector)
-40 ° C … 85 ° C (without mechanical drive)
Maneuver cycles > 100
Head 1
Head structure Female
Head cable outlet right
Head thread type M12
Coding coding B
Head 2
Head structure free conductor end
No. poles 2
Coding B – reverse
Maneuver cycles > 100
Connection PROFIBUS
Contact material CuZn
Contact surface material Ni / Au
No. poles 2
Coding B – reverse
Maneuver cycles > 100
Connection PROFIBUS
Contact material CuZn
Contact surface material Ni / Au
No. poles 2
Coding B – reverse
Maneuver cycles > 100
Connection PROFIBUS
Contact material CuZn
Contact surface material Ni / Au
Impulsive dimensioning voltage 1.5 kV
Mass resistivity ≤ 3 mΩ
Insulation resistance ≥ 100 MΩ
Rated voltage U N 48 V AC
60 V DC
Rated current I N 4 A (Male / female connector according to IEC 61076-2-101, observe the technical data of the cable)
Test voltage 2500 V
Transmission medium Copper
Contact us to discover 1525610. ICDCSPARES.COM offers new or overhauled original components, ready in stock to be shipped via DHL Express! Call us!
Check our Electrical section to discover more about ICDC catalog: a large selection of industrial spare parts including Fuses, Electric Motors, Switches and Connectors-Contactors.
Are you looking for industrial Connectors-Contactors?
ICDC offers online a wide selection of Connectors-Contactors of the most important OEMs like EATON, ABB and DANFOSS, besides PHOENIX.ICDC, Your Industrial One Stop Shop for Components!